[ Greater Los Angeles · Electrical Contractors ]
Power, engineered
for Los Angeles.
Power when you need, efficiency in your bill.
Panel upgrades, residential, commercial, industrial and motor control work — planned, permitted and installed by one accountable team. Workmanship and lifetime guarantee included.
Now serving
Greater Los Angeles
Emergency service
Panels, outages, motor faults
- Licensed · Bonded · Insured
- Lifetime workmanship guarantee
- Residential · Commercial · Industrial
- Free written estimates
[ Scope of work ]
Five disciplines.
One set of hands.
From a 100A house panel to a 480V motor control line-up, the same team plans the load, pulls the permit and stands behind the installation. No handoffs, no gaps in accountability.
Residential
Whole-home rewires, remodels, lighting design and quiet troubleshooting for houses, condos and ADUs across the city.
- Whole-home rewires and knob-and-tube replacement
- Kitchen, bath and ADU rough-in and finish
- Architectural and landscape lighting
Panel Upgrades
Service and distribution upgrades from 100A residential panels to 1200A three-phase switchgear — load calculated, permitted and inspected.
- 100A–1200A service and sub-panel upgrades
- Single-phase to three-phase conversions
- EV-ready capacity and load calculations
Commercial
Tenant improvements, restaurants, retail and office build-outs delivered on schedule and to plan, around your operating hours.
- Tenant improvements and build-outs
- Restaurant and retail power and lighting
- Panel schedules, as-builts and code compliance
Industrial
480V distribution, machinery hookups and power quality work for manufacturers, warehouses and processing facilities.
- 480V distribution and busway installation
- Equipment and machinery power connections
- Power quality studies and harmonic correction
Motor Control
Motor control centers, VFDs, starters and phase monitoring built for equipment that cannot afford to stop.
- MCC installation, rebuilds and line-ups
- VFD and soft-start commissioning
- Across-the-line and reduced-voltage starters
[ Not sure where it fits? ]
Tell us what is happening. We will scope it correctly.
Start a conversation[ Phase & flow ]
Two legs, three phases.
One balanced load.
Most residential and commercial power problems are not power problems at all — they are balance problems. When the legs or phases carry unequal current, equipment runs hot and the meter charges for it. Here is what we look at, and what changes when the load is set right.
Figure 01
Residential split-phase · 120/240V
A home runs on a single phase split into two legs, 180° apart. Each leg delivers 120V to neutral for lights and outlets; together they add to 240V for the dryer, oven, EV charger and A/C. Sharing loads evenly across both legs is what keeps a residential panel balanced.
L1–N
120V
L2–N
120V
L1–L2
240V
Figure 02
Leg balancing
Most circuits landed on one leg — flicker under load, a warm neutral and a panel that trips when the A/C and oven run together.
Figure 03
Residential bill, before and after
Illustrative model
Residential split-phase
Peak draw
Neutral current
TOU peak bill
A balanced split-phase service pulls less peak current, drops the neutral to nearly nothing and trims the time-of-use bill. Actual results depend on your load and utility rate — we measure before quoting.
Figure 04
Three-phase waveform
Each phase peaks 120° after the last. That rotation is what keeps motors turning smoothly and transformers evenly loaded — and what goes wrong when a panel is wired without a load calculation.
Figure 05
Phase balancing
Phase A carries nearly three times the load of Phase B — hotter conductors, nuisance trips and a demand charge you should not be paying.
Figure 06
Commercial bill, before and after
Illustrative models
Commercial 3-phase
Peak demand
Power factor
Monthly demand charge
A balanced service runs cooler, trips less and bills lower. Actual results depend on your load profile and utility rate structure — we measure your service before quoting any efficiency work.
The Combo standard
Workmanship and lifetime guarantee included.
[ Why it holds up ]
The difference is in what you never have to think about again.
Anyone can make a circuit work for a week. We build for the next thirty years of heat, load and remodels — which means real load calculations, correctly sized conductors, and an installation a future electrician will thank us for.
Workmanship and lifetime guarantee included
If our workmanship fails, we return and correct it. That commitment ships with every job, written into the estimate — not buried in fine print.
Licensed, bonded and insured
Fully credentialed California electrical work, with the coverage and paperwork that protects your property and your project.
Permits and inspections handled
We pull the permit, meet the inspector and close the job out — so the work on your wall is documented and insurable.
Labeled, torqued and handed over clean
Every circuit identified, every termination torqued to spec, every panel photographed and documented before we leave.
[ Service area ]
Los Angeles, corner to corner.
We work across the city and its neighboring valleys, beaches and foothill towns. Same crew, same standard, same guarantee wherever the truck lands.
Not on the list? We still travel for scheduled work — call 818-761-1909 and we will confirm coverage.
Central & Downtown
- Downtown LA
- Silver Lake
- Echo Park
- Koreatown
- Mid-City
- Hollywood
Westside
- Santa Monica
- Beverly Hills
- Culver City
- Brentwood
- West LA
- Marina del Rey
San Fernando Valley
- Sherman Oaks
- Studio City
- Van Nuys
- Woodland Hills
- Burbank
- Glendale
- Agoura Hills
South Bay
- Torrance
- Redondo Beach
- Manhattan Beach
- El Segundo
- Inglewood
- Long Beach
San Gabriel Valley
- Pasadena
- Arcadia
- Alhambra
- Monrovia
- San Marino
Ventura County & Surrounding
- Ventura
- Oxnard
- Thousand Oaks
- Simi Valley
- Camarillo
- Moorpark
- Newbury Park
- Conejo Valley
Los Angeles County and surrounding areas
Emergency response · 24 hours
[ FAQ ]
Questions, answered straight.
The things most customers ask before reaching out. If your question is not here, the fastest answer is a phone call.
Use the contact form or call us directly. For most jobs we schedule a quick site visit, measure the actual load and scope, and send a written estimate — usually within two business days. There is no charge for the first visit.
Yes. We carry a California electrical contractor license, a surety bond and full liability coverage. Proof of insurance and licensing is included with every estimate on request.
We pull the permit, schedule the inspection and close it out for every job that requires one. You never deal with the city yourself — the work on your wall is documented and insurable when we leave.
Greater Los Angeles and the surrounding valleys, beaches and foothill towns — from Downtown to Ventura County. If you are outside the listed cities, call us and we will confirm coverage for scheduled work.
Yes. We respond to outages, panel faults and motor failures 24/7 across the service area. Weekday hours cover scheduled work; nights and weekends cover emergency calls only.
Every job ships with a workmanship and lifetime guarantee. If our workmanship fails, we return and correct it at no cost — written into the estimate, not buried in fine print.
[ Next step ]
Power when you need, efficiency in your bill.
Send the details or call the direct line. We answer, scope it honestly, and put the estimate in writing.